---
title: "Aluminium Electric Gates in Chigwell | Chigwell Electric Gates"
description: "Lightweight aluminium electric gates with automation. Low-maintenance, corrosion-resistant entrance solutions installed to DHF and Gate Safe standards."
canonical: "https://www.chigwellelectricgates.co.uk/services/aluminium-electric-gates"
lastmod: "2026-11-15T10:01:50.050Z"
---

# Aluminium Electric Gates in Chigwell

![A modern grey automatic sliding gate at the entrance to a residential property's driveway, flanked by brick pillars and green hedges.](https://utmost-ibex-736.convex.cloud/api/storage/ac31a9d7-5938-4430-a1fc-28afd46ff3ee)

A lighter gate, a smaller motor, and a powder-coated finish that holds its colour without repainting.

- **Survey & Specification**: We schedule a survey, specification and quote for the full job.
- **DHF & Gate Safe**: Safety edges and photocells specified to DHF and Gate Safe standards.
- **Groundwork & Wiring**: Foundations and 18th Edition wiring quoted as part of the same job.
- **Any RAL Colour**: Powder-coated finish applied over aluminium primer in your chosen colour.

## Where rushed aluminium gate installations fall short

Cutting corners on motor spec, finish prep, or sensor compliance creates problems that show up within the first year.

- **Oversized Motor**: Fitting a steel-rated motor to aluminium leaves wastes energy, increases wear on hinges, and raises the cost of the whole installation.
  **Load-Matched Operator**: A site survey measures gate leaf weight and opening width so the operator is sized to the actual load, not a generic estimate.
- **Bare Finish Failure**: Aluminium painted without a primer coat oxidises beneath the surface, causing the finish to bubble and peel within a few seasons.
  **Primed Powder Coat**: Powder coating applied over an aluminium-specific primer bonds properly and resists corrosion without the need for periodic repainting.
- **No Safety Sensors**: A powered gate without compliant safety edges and photocells fails BS 13241 and creates a crush risk that leaves the owner liable.
  **BS 13241 Compliance**: Safety edges and photocells are specified to DHF and Gate Safe standards on every installation, with force testing on commissioning.
- **Wrong Opening Style**: Swing gates fitted where the driveway slope or available space is too tight bind on the ground or block the road when fully open.
  **Swing or Sliding Survey**: The site survey checks ground level, entrance width, and available run-back before swing arms or a sliding track is specified.

## What the installation covers

From gate leaf fabrication to control panel commissioning, every element is quoted as part of the same job.

- **Swing Aluminium Gates**: Hinged gate leaves on ram or articulated arm operators, sized to the entrance width and ground clearance confirmed at survey.
- **Sliding Aluminium Gates**: Single-leaf sliding gates on a ground track or cantilever system where driveway space rules out a swing configuration.
- **Powder-Coated Finish**: Any RAL colour applied over aluminium primer, giving a corrosion-resistant finish that does not need repainting to maintain its appearance.
- **Gate Motor & Control Panel**: Motor, control panel, remote fob, and optional keypad or app-based access specified, installed, and commissioned in a single visit.
- **Safety Sensors & Compliance**: Safety edges and photocells fitted and force-tested to BS 13241 and DHF and Gate Safe standards before the installer leaves the site.

- **Remote Fob Access**: Open and close the gate from inside the car.
- **Keypad Entry**: PIN-code access for visitors or deliveries.
- **App-Based Control**: Operate the gate from a smartphone app.
- **Groundwork & Wiring**: Post foundations and 18th Edition cabling included.

## Why aluminium changes the motor spec and the long-term upkeep

Aluminium’s lower weight affects every part of the installation, from motor selection to the size of the post foundations needed.

Steel and timber gates are heavier, which means larger motors, stronger post foundations, and more frequent hinge servicing. Aluminium gate leaves reduce that load considerably, allowing a lighter operator and smaller fixings without compromising the gate’s rigidity. For Chigwell driveways where the entrance already has established brickwork, that lower load matters.

Powder coating is applied over an aluminium primer in any RAL colour, giving a finish that does not rust and holds its colour without repainting. A site survey covers entrance width, ground level, and whether swing or sliding suits the available space, measurements that determine gate leaf size and the track or hinge configuration before fabrication begins.

Safety sensors are specified to BS 13241 compliance on every installation. The control panel, remote fob, and any keypad or app-based access are commissioned and tested during the same visit, so the gate is fully operational by the end of the visit.

[Request a Survey](https://www.chigwellelectricgates.co.uk/contact)

## Why choose us for aluminium electric gates in Chigwell?

We schedule the survey, specification, and installation, with compliance and accountability built into every job.

- **Full-Job Quoting**: Groundwork, post foundations, and 18th Edition wiring are quoted upfront, no surprise additions after the survey.
- **DHF & Gate Safe Standards**: Every installation is specified to DHF and Gate Safe standards, covering safety edges, photocells, and force testing.
- **Local Site Surveys**: We schedule surveys that cover Chigwell driveways and Essex property layouts.
- **Single-Visit Commissioning**: Motor, control panel, remote fob, and sensors are all commissioned and tested before the installer leaves your property.
- **Survey Before Fabrication**: Gate leaves are not fabricated until the site survey confirms exact measurements, opening style, and ground conditions.

## From first enquiry to a working gate

1. **Describe Your Entrance**: Tell us the gate width, driveway slope, and power available and we’ll schedule a survey and quote the full job.
2. **Survey & Specify**: The site visit measures the entrance, confirms swing or sliding, and specifies the motor, track or hinges, and safety sensors.
3. **Install & Commission**: Gate leaves, operator, control panel, and sensors are fitted and tested to BS 13241 compliance before the installer leaves the site.

[Request a Survey](https://www.chigwellelectricgates.co.uk/contact)

## Typical Aluminium Electric Gates Prices

| Job | Typical cost |
| --- | --- |
| Pair of aluminium gates | £1,500-£5,000 |
| Aluminium swing gate system | £2,500-£6,000 |
| Fully installed aluminium gate system | £3,500-£10,000 |

These prices are estimates and often vary with the condition, size and scope of each job. Message us for a free, no-obligation quote.

[See all prices](https://www.chigwellelectricgates.co.uk/pricing)

## Questions about aluminium electric gates

### How much do aluminium electric gates cost to install?

Guide prices run from £1,500-£5,000 (Pair of aluminium gates) to £3,500-£10,000 (Fully installed aluminium gate system). The final figure shifts based on gate size, entrance width, chosen operator, and whether groundwork or new cabling is needed.

### What affects the cost of aluminium electric gates?

Gate width and height have the biggest effect, as larger panels need heavier operators. Beyond that, the type of automation (swing or sliding), the length of cable run, any groundwork for posts or a sliding track, and the access control system all add to the total.

### Is an aluminium electric gate right for my driveway layout?

It depends on entrance width, available swing or slide clearance, and ground conditions. A site survey assesses all of these and recommends the right gate style and operator for your specific layout, so you get a system that works reliably day to day.

### Which is better for me, a swing gate or a sliding gate?

Swing gates suit wider entrances with clear space behind the gate line. Sliding gates work better on sloped driveways or where space is tight. A survey measures your entrance and ground gradient to confirm which type operates safely and reliably at your property.

### Do I need planning permission to install electric gates?

Gates up to 1 metre on a road boundary, or 2 metres elsewhere, generally fall within permitted development and need no planning application. Taller gates, listed buildings, and properties in conservation areas may require consent. Check with your local planning authority before ordering.

### Will the installation need electrical or ground work?

Almost always, yes. A mains power supply needs routing to the operator, and posts or a sliding track may require concrete foundations. The survey scopes both elements and includes them in the quote, so groundwork and wiring are planned from the start rather than added later.

### How much disruption should I expect during installation?

Most installations take one to two days. There will be some digging for posts or track foundations and cable routing, but the driveway surface is typically restored before the installer leaves. Your entrance will be accessible again once the gates are commissioned and tested.

### What happens if the automation fails or needs repair?

Every automated gate has a manual release so you can open it by hand while a repair is arranged. If the automation fails, delaying a repair risks the gate becoming stuck closed or open, which is both a security and a safety issue. Prompt attention keeps the system compliant and usable.

### Which areas do you cover for Aluminium Electric Gates?

We cover Aluminium Electric Gates in and around Chigwell, including Buckhurst Hill, Loughton, Abridge, Theydon Bois, Epping, Upminster and Gidea Park. If your area isn’t listed, [send us a quick message](https://www.chigwellelectricgates.co.uk/contact) to check.

## Tell Us About Your Entrance

Describe the gate width, driveway layout, and access you need and we’ll schedule a survey, specification and quote for the full job, groundwork, wiring, and safety sensors included.

[Request a Survey](https://www.chigwellelectricgates.co.uk/contact)

## Business details

### Contact

- **Email**: [contact@chigwellelectricgates.co.uk](mailto:contact@chigwellelectricgates.co.uk)
- **Based in**: Chigwell, Essex, IG7 6NX
- **Enquiries**: [Send an enquiry](https://www.chigwellelectricgates.co.uk/contact) — We ask for your name, phone number, email and a message.

### Opening hours

- **Monday**: 08:00 – 18:00
- **Tuesday**: 08:00 – 18:00
- **Wednesday**: 08:00 – 18:00
- **Thursday**: 08:00 – 18:00
- **Friday**: 08:00 – 18:00
- **Saturday**: 10:00 – 16:00
- **Sunday**: 10:00 – 16:00
