---
title: "Automated Swing Gates in Chigwell | Chigwell Electric Gates"
description: "Automated swing gate installation with proper operator sizing and safety compliance. Fitted to your entrance width and traffic flow requirements."
canonical: "https://www.chigwellelectricgates.co.uk/services/automated-swing-gates"
lastmod: "2026-11-15T10:01:50.050Z"
---

# Automated Swing Gates in Chigwell

![A modern light grey double gate with an intercom keypad stands at the entrance of a gravel driveway, flanked by green hedges.](https://utmost-ibex-736.convex.cloud/api/storage/bc2a0c20-ee48-47ad-9694-fae6080f8cbf)

Your driveway gate opens and closes on its own, matched to the right motor and wired to standard.

- **Survey & Specification**: A site survey covers your entrance and specifies the right operator.
- **DHF & Gate Safe**: Safety edges and photocells specified to DHF and Gate Safe standards.
- **Wiring Included**: Groundwork and wiring quoted as part of the same job.

## Where swing gate automation goes wrong

The most common faults trace back to decisions made before the motor is ever fitted.

- **Undersized Motor**: A motor rated below the gate’s actual weight strains on every cycle and fails within months.
  **Weight-Matched Motor**: Motor selection is confirmed from survey data, gate weight and leaf width measured on site, not estimated.
- **Worn Hinges Ignored**: Automating a gate with worn or loose hinges transfers the load to the motor arm, causing drift and misalignment.
  **Hinge & Post Check**: A pre-installation check confirms hinge condition and post rigidity before any motor is specified or ordered.
- **Wrong Arm Geometry**: Incorrect gate arm positioning creates binding at mid-travel, which trips the motor’s overload protection repeatedly.
  **Arm Geometry Set on Site**: The installer sets arm pivot points to the gate’s actual opening arc, then adjusts controller limit settings for a clean stop.
- **Non-Compliant Wiring**: Power supply wiring run outside BS 7671 requirements creates a safety risk and can void any access control warranty.
  **BS 7671 Wiring**: All controller and power supply wiring is installed to BS 7671 18th Edition standards as part of the same visit.

## What swing gate automation covers

From a single gate on a home driveway to a double-leaf entrance on a larger plot, the scope is the same: assess, specify, fit, and test.

- **Single Swing Gate Automation**: One motor and gate arm fitted to a single leaf, with controller wiring and a final open/close test on completion.
- **Double Swing Gate Automation**: Two motors synchronised through a single controller, with limit settings adjusted so both leaves close at the same point.
- **Existing Gate Conversion**: A suitability check on your current gate, hinges, and posts before the motor kit is specified, no unnecessary replacement.
- **Access Control Integration**: Keypad, remote, or app-based access control wired to the gate controller as part of the same installation.

- **Pre-Installation Survey**: Alignment, hinge, and post check before any parts are ordered.
- **Motor & Arm Fitting**: Motor and gate arm positioned to the gate’s opening arc.
- **Controller Wiring**: Controller and power supply wired to BS 7671 standard.
- **Safety Device Specification**: Safety edges and photocells to DHF and Gate Safe standards.

## Automating a swing gate: what the assessment covers and why it matters

Fitting a motor to an existing swing gate starts with checking whether the gate and its posts can handle the load.

Many Chigwell properties already have swing gates in place, the question is whether they are suitable for automation. A pre-installation check covers hinge wear, post rigidity, gate alignment, and the available opening arc. A gate that binds, sags, or sits out of plumb will cause motor strain and early failure if automated without remedial work first.

Once the gate passes the suitability check, the motor and gate arm are matched to the gate’s weight and leaf width. Undersized motors are a common cause of intermittent faults, so the motor-to-gate weight match is specified from the survey data, not estimated. The controller is wired to BS 7671 standards and limit settings are adjusted for a clean stop at both ends of travel.

A DIY automation kit may appear straightforward, but incorrect arm geometry or a missed hinge fault leads to gate drift and sensor misalignment within months. We schedule the full conversion, assessment, fitting, wiring, and a final open/close test, so the gate operates reliably from day one.

[Request a Survey](https://www.chigwellelectricgates.co.uk/contact)

## Why use us for swing gate automation in Chigwell?

We schedule the full job, survey, fitting, wiring, and safety specification, under one arrangement.

- **Survey Before Specification**: A site visit comes first. Nothing is ordered until the gate, hinges, and posts are confirmed as suitable.
- **DHF & Gate Safe Compliance**: Safety edges and photocells are specified to DHF and Gate Safe standards on every swing gate installation.
- **BS 7671 Wiring as Standard**: Controller and power supply wiring meets BS 7671 18th Edition requirements, not an optional add-on.
- **One Quote, Full Scope**: Groundwork, wiring, and access control are quoted together, so there are no separate invoices or gaps in accountability.
- **Local Installer Knowledge**: Installers familiar with Essex period entrances and Chigwell driveway layouts handle the survey and fitting directly.

## From first enquiry to a working gate

1. **Describe Your Gate**: Tell us the gate width, leaf weight, slope, and power available so we can schedule the right survey for your site.
2. **Survey & Specify**: The installer checks hinge condition, post strength, and alignment, then specifies the motor, arm, and controller to match.
3. **Fit, Wire & Test**: Motor, arm, and controller are fitted and wired to BS 7671, then tested through a full open/close cycle before sign-off.

[Request a Survey](https://www.chigwellelectricgates.co.uk/contact)

## Typical Automated Swing Gates Prices

| Job | Typical cost |
| --- | --- |
| Basic single swing gate | £2,500-£6,000 |
| Double swing gates | £4,500-£10,000 |
| Metal swing gate system | £7,000-£7,500 |
| Wooden swing gate system | £7,500-£8,000 |

These prices are estimates and often vary with the condition, size and scope of each job. Message us for a free, no-obligation quote.

[See all prices](https://www.chigwellelectricgates.co.uk/pricing)

## Swing gate automation: questions answered

### Why is my automated swing gate not opening properly?

The most common causes are a faulty limit switch, a worn motor, or an obstruction the safety edge has detected. Low battery in the control board or a misaligned photocell can also prevent movement. Check for debris along the gate’s travel path first, then check the control panel for fault codes. A [repair callout](https://www.chigwellelectricgates.co.uk/services/electric-gate-repair-emergency-callouts) can diagnose and fix most faults in a single visit.

### Why does my swing gate keep stopping halfway?

A gate stopping mid-travel usually means the motor’s torque setting is too low, a safety edge is triggering falsely, or the gate has developed a mechanical drag, often from a sagging hinge or ground contact. Adjusting the torque limit or realigning the gate leaf resolves most cases. Ignoring it risks burning out the motor over time.

### Can my existing swing gate be automated?

Most existing swing gates can be automated, provided the posts and hinges are structurally sound and the gate is in reasonable condition. A site survey checks post depth, hinge load capacity, and available space for the operator arm. Gates that are rotten, badly warped, or hung on inadequate posts usually need remedial work first. See [gate automation retrofitting](https://www.chigwellelectricgates.co.uk/services/gate-automation-retrofitting) for more detail.

### Is my gate too heavy or awkward to automate?

Swing gate operators are available for leaves ranging from lightweight timber up to heavy wrought iron exceeding 500 kg. The key factor is matching the operator’s rated torque to the gate’s actual weight and width. A survey measures both and specifies the correct motor class, so oversized or unusually heavy gates are not automatically ruled out.

### Will an automation kit fit my existing gate?

Fit depends on the gate’s weight, leaf width, hinge type, and the clearance behind the post for the operator arm. Underground ram systems suit gates where above-ground arms would look out of place. A survey confirms which operator type and mounting configuration works before any parts are ordered.

### How much does it cost to install automated swing gates?

Guide prices run from £2,500-£6,000 (Basic single swing gate) to £4,500-£10,000 (Double swing gates). Underground ram operators and bespoke gate leaves sit at the higher end. A site survey produces an itemised quote covering all labour, materials, and wiring.

### What affects the cost of automating a swing gate?

The main cost drivers are the gate’s weight and width (which determine motor class), whether you choose above-ground arms or underground rams, the amount of groundwork and cable trenching needed, and any access control or intercom additions. Retrofitting to an existing gate is generally less expensive than a full gate-and-automation supply.

### What is checked before fitting a swing gate motor?

The installer checks post depth and rigidity, hinge load rating, gate weight and leaf width, available space for the operator arm, and the condition of the gate structure. Electrical supply routing and earthing are also assessed. Safety edge and photocell positions are specified to DHF and Gate Safe standards before any fitting begins.

### Which areas do you cover for Automated Swing Gates?

We cover Automated Swing Gates in and around Chigwell, including Buckhurst Hill, Loughton, Abridge, Theydon Bois, Epping, Upminster and Gidea Park. If your area isn’t listed, [send us a quick message](https://www.chigwellelectricgates.co.uk/contact) to check.

## Tell Us About Your Entrance

Describe the gate, driveway, and access you need and we’ll schedule a survey and quote the full job.

[Request a Survey](https://www.chigwellelectricgates.co.uk/contact)

## Business details

### Contact

- **Email**: [contact@chigwellelectricgates.co.uk](mailto:contact@chigwellelectricgates.co.uk)
- **Based in**: Chigwell, Essex, IG7 6NX
- **Enquiries**: [Send an enquiry](https://www.chigwellelectricgates.co.uk/contact) — We ask for your name, phone number, email and a message.

### Opening hours

- **Monday**: 08:00 – 18:00
- **Tuesday**: 08:00 – 18:00
- **Wednesday**: 08:00 – 18:00
- **Thursday**: 08:00 – 18:00
- **Friday**: 08:00 – 18:00
- **Saturday**: 10:00 – 16:00
- **Sunday**: 10:00 – 16:00
